SIMPLIFY 3D AND REPETIER SERVER FULL
SIMPLIFY 3D AND REPETIER SERVER CODE
SIMPLIFY 3D AND REPETIER SERVER PLUS
SIMPLIFY 3D AND REPETIER SERVER SERIES

Stepper control is handled in an interrupt routine, leaving time for.Multi-Language support, switchable at runtime.Detection of heater/thermistor decoupling.Important parameters are stored in EEPROM and can easily be modified without recompilation of the firmware.Autodetect the command protocol, so it will work with any host software.Standard ASCII and improved binary (Repetier protocol) communication.Fast - 40000 Hz and more stepper frequency is possible with a 16 MHz AVR.Nozzle pressure control for improved print quality with RAMPS.Trajectory smoothing for smoother lines.Supports cartesian, delta and core xy/yz printers.This is just a small bit of credit to me - this firmware configuring, setup and testing took months to date. This D5S specific version is developed by Jaco Theron from XiliX Technologies.īy default the printer will display 'XiliX Tech' on the logo screen, you are allowed to remove or change this.

SIMPLIFY 3D AND REPETIER SERVER PLUS

plus several small contributions from other users.

SIMPLIFY 3D AND REPETIER SERVER CODE

sdavi (first u8glib code implementation).

Martin Croome (first delta implementation).

It was initially based on the Sprinter firmware from Kliment, but the code has run The sources are managed by the Hot-World GmbH & Co. The firmware Arduino File is located in 'Repetier/repetier.ino'įor now the firmware will not be in a ready to flash file format - you have the source to help debug and contibute to the development. The D5S mainboard is an Arduino Mega 2560 compatible board (you will need to select it from the Tools menu). In order to compile this, you will need Arduino IDE (the latest is able to compile this firmware). If your mainboard supports this, you can follow the guide.įor official Repetier documentation please visit While it is possible to make the D5S control a heatbed (through a Power Expander and separate power supply), this can only happen on the older mainboards (where there are more than one temperature sensing and control outputs).

You are free to make changes to the configuration.h file, for example setting up special features.

Some people report having access to variable fan speed control while using this firmware.

For subsequent changes, you may need to set the EEPROM mode to 1 or 2 (the number it is not currently).

EEPROM is enabled and thus a lot of values can be changed using Repetier Host.Stopping a print will Home the head in the X direction (I hated the head just remaining where it was), before disabling the steppers.Buzzer have been disabled, is was getting irritating (but you can enable it).

SIMPLIFY 3D AND REPETIER SERVER FULL

The Configuration file is not Assistant Tool ready, but it contains full comments.You are welcome to configure these in the firmware. Features that I do not use, was disabled.In order to use this, you have to create a voltage divider board/circuit (I made mine from standard stip board - tutorial coming soon). Made to use a 100k NTC 3950 thermistor in stead of the stock k-type thermocouple.Made to work with a D5S Mainboard and D5S screen (the screen uses non-standard pinouts and other requirements).Extrusion Calibration - ensure you are pushing the correct amount of filament to not be over or under extruding (this firmware allows E-steps calibration and then final adjustment from your slicer).PID Tune - this allows your printer to maintain temperature.Things can go wrong or simply with the new firmware the printer might be over extruding (better do those calibration cubes to get it perfect again).Īfter updating to this firmware, please perform the following: While this firmware should simply work, I advise against updating to it while you are busy with an important project. The newer version solves compiling errors. For the latest version (based on Repetier 1.0.3), please visit Repetier 1.0.3 Wanhao D5S This version is old, as of 21 January 2019. For this to work the pins.h for the Ultimaker board was modified.

SIMPLIFY 3D AND REPETIER SERVER SERIES

This repository contains a forked version of the original Repetier Version (0.92.9), which is specifically tailored for the Wanhao D5S series printers. Repetier-Firmware for D5S - the fast and user friendly firmware

Simplify 3d and repetier server